WTB SST60 exhaust addapter

[Fast Fred]

ya i need one, lets me know if ya gots one to sell.

[Fast Fred]

and this is what one looks like:cool:
http://i41.tinypic.com/r1g07r.jpg

[Fast Fred]

if ya got one 850cc:cool:

[850cc racer]

oh yeh i gots one. are these rare? cos i need mine, im not sure if i have a spare :cool:

is this something if i sent you mine you could get one cast?

p.s. will check spares on tuesday and see what i find

[Fast Fred]

be best to just buy one, got to cut the tuna off to cast it, but thanks
thay cast new ones at Seaway, can just get one there, but was thinkin i'd do some shoppin, was never good at shoppin, it's more like buyin stuff for me, cuzz i know what i want. new is right about 550 bucks.:eek::cool:

[Fast Fred]

seems like theirs a plug in that last post,:eek:
good used parts sell for about 50% of new, broken or hard salted , thinkin less, but show me whatchew got.:cool:

[SST60RYE]

i have a broken one, has damage to two of the wing plate holes on one side? can be fixed easily, has megaphone on it, let me know, thanks

[SST60RYE]

no longer available, thank you

[Fast Fred]

?????????, well got the last note, think it would have worked out best for me if i got the NOTE before the last one:eek: WTF:eek::cool:

[Fast Fred]

it's good to see the will to get your rig out there is doin well, seems just about anythig else $uck$. anyways still needs one, brokin, Modded, would all be considered:eek::cool: not runnin SST, runnin SLT, no rules on exhaust addapter (other than "must come out at the mid-section"):cool:

[Fast Fred]

still lookin:eek::cool:

[Roy Hodges]

How similar - or different is the mod 50 tuner , from the 56 incher tuner ? I guess the SST 60 tuna is different from the rest ? Where does Charlie Tuna fit in here ? Just digesting all this; OMC musta made a Bazillion different Tunas ? (for 3 cylinder 49 &56 inchers ? )

[Fast Fred]

http://i44.tinypic.com/10er5fd.jpg

[Fast Fred]

the 56er is the lowest one in the shot, mod50 and sst60 tunas are welded to the addapter, sst60 is like a square cow bell, got a twist in it, a bit of rectangle.
i made the 56er in the shot from a 20" mid. the sst60 addapter got cast in solid mounts, and steerin bar mounts too.

i tryed another 20" mid one, i don't like it, i want to start with an SST60 one.:cool:

[Detroit Whitey]

got a fishin exhast not gonna use

[Fast Fred]

what shaft is it for? i could never find a 56cuber 15" shaft unless it was a SST60. what height is it, and what ya need for it?:cool:

[Fast Fred]

haven't herd back from Whitey, ether way still be lookin for an SST60 addapter
for my SSTX60 project. hay Whitey call me?:eek::cool:

[Fast Fred]

http://i41.tinypic.com/257lu8x.jpg

[Detroit Whitey]

Sorry took so long its for the 4 lug shaft i found it on a 87 70hp it would be cool to use you could build all kinds differnt kinds of pipes and will bolt on.The down side is ya still have to build soild mounts for it

[Fast Fred]

cool, what ya need for it, no problem on the mounts. see the one under the lower unit, that was a 20" adapter, i cut it down but it don't line up well,
20" addapter is taller than the 15", what you got? a 15", a 20", is it a cut down,hows the bace gasket linein up?:cool:

i'll kick around some more lookin for an SST one, maybe even buy a new one, see if thay made any, or i'll trick out this one you got Whitey. i baged some shots of the stock tuna. it's for a new SLT, Xclass hull. I need to hear it thumpin soon:eek::cool::eek:

[Roy Hodges]

All 56 inchers were LONG shaft , except SST60's. 70 horse 49 inchers were all long shaft, EXCEPT in 1974 , i saw a 1974 short shaft 70 in the shipping box ,when new in 1974 at a local dealer. He got it by MISTAKE, and returned it to Johnson for a long shaft. I repeat , you need to cast your own .

[Fast Fred]

i hear ya, but thare are factors that make it not a good idea for this project.
one factor is i don't even have a crucible, another is time... guna be showtime for it vary soon. allreddy tossed $$$ at that 20"er only to look at it and say i'm not usein it.
it's not mine, best to use somethin factory until i got a made,and tested part.:cool:

[Detroit Whitey]

Is sea way still not makin the adapter.I had to buy a unfinished one and finish it off myself that still might be the way to go for ya

[Fast Fred]

called them about five times on one or two even.???????????, need one.:cool:

[Detroit Whitey]

Well if we all call them they will start making them i would buy like 4 of the things myself if we call them at least once a day it will happen i`m gonna i have had enough of this crap!!!!!!!!!!!! I`m gonna start makin this stuff myself :D

[Fast Fred]

i tryed to buy all the 3 cyl molds, but i did not know Cees, them Seaway guys had more $$$$ than i did. i got an unfinished addapter . :cool::eek::eek:

[Fast Fred]

seems a used one did turn up as well:cool: how are things up that way?:eek::cool:

[Powerabout]

Did anyone start casting them or how about getting a 3d scan

[850cc racer]

this might help? i dont have it anymore though

:cool:

[Powerabout]

Great thanks

Meg welded on was standard I beleive?

[850cc racer]

there was no bolting her on so i would say yes

[Fast Fred]

you want a drilled one, i've used a fresh case one, it was a pain to get it all drilled and machined.:cool:
hey 850cc

[Powerabout]

Yep. I'm after one

[Fast Fred]

you can cut down a 20" addapter, and it works:cool:

[Powerabout]

ya but what about the megaphone a std 20 its long and thin, the sst 60 looks a lot different?
Anyone got the dimensions of the sst 60 megaphone? The rule book only has the length.

Nice to get the lower pan mounts and the sold mounts as well