Page 43 of 85 FirstFirst ... 19202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667 ... LastLast
Threads 841 to 860 of 1691

Forum: Technical Discussion

  1. Smile Sticky Thread Sticky: Building A looper Beast

    Started by R Austin, 05-14-2012
    63 Pages •
    1 2 3 ... 63
    1021 Attachment(s)
    • Replies: 622
    • Views: 1,200,334
    R Austin
    07-17-2023 Go to last post

  1. 56 cu inch powerhead on a 49 cu inch adapter?

    Started by Billsboats, 01-02-2012
    • Replies: 4
    • Views: 2,793
    Billsboats
    01-02-2012 Go to last post

  2. Ethonol proof fuel lines

    Started by calvin, 03-16-2010
    ethonol, fuel, lines, proof
    • Replies: 4
    • Views: 2,873
    Popa Sam
    03-17-2010 Go to last post

  3. Glasspar g3 hull mods

    Started by PIP, 07-26-2011
    • Replies: 4
    • Views: 4,725
    rdr140
    12-07-2011 Go to last post

  4. Question 45-sst prop shaft pin

    Started by byrdsperformance@tds.net, 10-26-2011
    • Replies: 4
    • Views: 2,800
    byrdsperformance@tds.net
    10-27-2011 Go to last post

  5. transom cutting

    Started by thunderstruck, 11-27-2011
    merc, omc, tunnel, twister
    • Replies: 4
    • Views: 6,118
    MN1
    11-27-2011 Go to last post

  6. speedmaster dimensions

    Started by thunderstruck, 12-17-2011
    merc, omc, quickfoot, stinger
    • Replies: 4
    • Views: 3,432
    MN1
    12-18-2011 Go to last post

  7. omc mod-50 flywheel puller

    Started by byrdsperformance@tds.net, 12-20-2011
    • Replies: 4
    • Views: 2,450
    byrdsperformance@tds.net
    12-22-2011 Go to last post

  8. OMC Twin 15" mid questions

    Started by ultrafast30, 01-17-2012
    • Replies: 4
    • Views: 2,077
    ultrafast30
    01-18-2012 Go to last post

  9. 40 nissan

    Started by cdixon4950, 02-10-2012
    • Replies: 4
    • Views: 2,674
    cdixon4950
    02-15-2012 Go to last post

  10. would these be the right carb numbers for 40hp mercury

    Started by Nason, 02-22-2012
    • Replies: 4
    • Views: 3,244
    25XS
    02-23-2012 Go to last post

  11. I want to make me a set of sst 60 lower mounts

    Started by tunnelvision07, 02-29-2012
    • Replies: 4
    • Views: 2,871
    tunnelvision07
    03-02-2012 Go to last post

  12. sst90 left hand flywheel needed

    Started by 777 racing, 03-09-2012
    • Replies: 4
    • Views: 2,405
    Fastjeff57
    03-10-2012 Go to last post

  13. intake vents?

    Started by cdixon4950, 03-09-2012
    1 Attachment(s)
    • Replies: 4
    • Views: 2,691
    fyremanbill
    03-12-2012 Go to last post

  14. Shift linkage question 56 cuber to 49 cuber parts

    Started by Billsboats, 03-21-2012
    • Replies: 4
    • Views: 2,216
    sharpeye Mike
    03-23-2012 Go to last post

  15. Mark 55H

    Started by Dockbuster, 03-22-2012
    • Replies: 4
    • Views: 2,855
    Fastjeff57
    03-23-2012 Go to last post

  16. Exclamation 3 cyl.OMC Stator Question

    Started by Billsboats, 04-02-2012
    • Replies: 4
    • Views: 8,518
    Billsboats
    04-02-2012 Go to last post

  17. Lets get bstarted

    Started by Aeroliner, 08-28-2012
    • Replies: 4
    • Views: 3,236
    jeeperstoys
    09-13-2012 Go to last post

  18. Question Setup/Engine advice for "fast" jon boat

    Started by TooQuick, 04-26-2013
    flatboat, jon boat 1 Attachment(s)
    • Replies: 4
    • Views: 17,918
    TooQuick
    04-28-2013 Go to last post

  19. Boat set up

    Started by Rabbitdundied, 04-25-2014
    • Replies: 4
    • Views: 3,380
    omcstratos
    04-26-2014 Go to last post

  20. Large taper vs. Small taper

    Started by GHMiller, 04-19-2014
    3 Attachment(s)
    • Replies: 4
    • Views: 3,387
    GHMiller
    04-19-2014 Go to last post
Page 43 of 85 FirstFirst ... 19202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 14 replies or 66 views
Hot thread with unread posts
More than 14 replies or 66 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules