Printable View
My new style tiller arm is set up to push when the throttle is twisted open. However on my 70 hp Yamaha the carb linkage needs to be pulled open. What is the easiest way to correct this? Do I need to take the inside gears out and flip them?
http://i163.photobucket.com/albums/t...ok/NEWMOTA.jpg
you can do that that is how mine is done
I got everything to work by flipping it to the other side, Im just running into a linkage problem now im trying to sort out.
Once you flip there should be any problems but there always is a chance let me know what you are running into and I can help
Ill get some pictures of the inside of the handle for you tomorrow
Been there done that.
Open the tiller. The handle drives a gear that on an axle. Turn that gear around to the other side of the axle.
You will lose the shift function.
I have an 02 yammi 90. Will a 40 tiller fit or be modified to fit? If not where can I find one that will fit?
xpress, the 60/70 takes a longer black plastic adapter that the other engines.
river rat, no. the yoke on the 40 is much shorter. You will have to have the 90 yoke. Also I have the block ready for you.
What tiller is best suited to a yamaha 70? Preferably with shift on the tiller as well
they made an Enduro handle. reg. and long. it is about the best there is
Thanks Fred,
so it looks like I'm after the tiller, cowling and pullstart from a Yamaha Enduro 60 - to convert a 70 for SLT use
you need to weld the crank on the 60- 70hp if you are goin to turn it over 6500rpms, 90 hp carbs are a must have, loose the choke plates= 2hp, 160 main jet, clip the tail off the wist pin clip
she don't like a lot of timin at big rpm, 17-18 deg max advance, on an SLT turn to 7800rpms
Cheers Fred, it's not a CES, just a shortened 70, all those things the same? Do you get boyesen reeds for them?
I have the rope start and cowl, I think the shipping will be massive.
I imagine it would be! I'll try and find one in the UK, could you see if you can get me a rough quote for shipping? CheersQuote:
Originally Posted by 88workcar
all the same on the 70hp, ces has a better exhaust cut
OK. so are the powerheads the same? do they both make 70hp at the same RPM?Quote:
Originally Posted by Fast Fred
Is it possible to put a ces exhaust tuner on a standard 70?
hey fred how hard do these 70 yams go ,i remember you sayin a while back they hang with the omc's.
i been in slt years ago with a 70 ces ,told me i'd ****e my pants ,but truthfully i was disapointed .he was runnin a modded 15p vengence ,i'm hoping he was the one that was ****ing his pants ???
i know forsure guys over here were hitting around 105kph on the old z9 hulls with 17p props.they couldn't do better cause of the hull wanting to blow over.
what are you guys runnin on an aqarius hull?
the record is 119kph with a fifty toaster .eek.
Who's record is that ?
Quote:
Originally Posted by fs5
RECORD No DATE PILOTE NAT. CLASS ENGINE HULL MPH KMHQuote:
Originally Posted by FrenchPhil
3731 2010 R. Sjögren GBR CIRCUIT P750 M ROWAN HAWKES TOHATSU 74,14 MPH 119,31 KMH
Pretty impressive with a tohatsu 50!
hears a shoot of the long handle
Looks like a pretty cool setup there Fred. Electric fuel pump? Where is your gear shifter?
shifta
this may help you control her better, steering dampener, does what it says, bungee and blocks for torque steer ............
Having problems getting my throttle cable to work, still pushes open but the carbs need pull to open. How do I go about flipping this gear?
http://i1013.photobucket.com/albums/...t/IMG_6834.jpg
http://i1013.photobucket.com/albums/...t/IMG_6835.jpg
don't think that tiller will pull, only push. 4 stroke tiller, you could move the pin then push would work.
Thanks Fred, not what I wanted to hear! haha
So is there a difference between my tiller and the one in the first photo on page 1?
maybe it can be done, move the side gear to the other side,? would need to see it
Anyone know if I can use a complete linkage from a newer 60/70hp? To change it from push to pull
If you require pull to open throttle you have to go olderQuote:
Originally Posted by Roflhat
Newer pushs older pulls
Ive overcome it before with chainging the black plastic carby advancer
Alright, you got any photos of what you did?
Apparently the newer block castings have an additional lug for mounting a cable reversing of some sort
Fast Fred will the long enduro tiller handle fit a mid 90's 40hp 3 cyl.? If so where can I get one?