Search:

Thank you 3030..!

Thank you guys...!, but someone is using same left flywheel, clockwise starter, and trigger relocated, and is working, but I have doubts about flywheel, because you have to find exact TDC, and mark...

Hi Everyone:
Need the correct procedure to make a left run sst120 powerhead, to clockwise.
Thanks

Thank you very much..!

This cylinder head came from my father´s shop
I do not remember which model & HP was
54475

The boat is ready and was tested first with a 175 Block, 6,300 rpm, with the prop you sold me, the boat raises the bow a lot, We put a new hub on a 28" pitch merc cleaver, got a 200 block, change...

Yes We did our best with the preparation, and carefully we applied all the layers, with the exact amount of everything...
wood Structure was cutted and fixed until perfect fit..
Now, We are fixing...

Thanks for the bump, the problem is that We can´t have Epoxy so easy down here, Import cost is High, but we are doing our best with wood, and fiber & resin work, your boat looks Fantastic..!:cool:
I...

Hi folks:
I´m rebuilding a laser boat (copy made in Mexico), `cause I`m going racing again..!:o
so, if anyone can help with ideas, tips and mods to the pad..or the entire hull
I`ll be happy to...

[QUOTE=Ron Hill;34214]There were some other pictures of Pat Bowman's Laser, from Parker.... But I wanted everyone to see the semi completed project.


How much this boat should weight..?
no...

Thanks, Hope not to replace ECU and PowerPack, owner will cry..!

Best Regards

Yes, after some research and consulting information I have the whole picture about this system, everything is working properly, but powerpack.
Have to find another to replace the fried one..
thanks

Did not complete data cable, but I did what you said, checked voltage, and is fine, ECU es working, Ignition module is faulty, looking for used one with some friend dealers down here
found some kind...

YEP..I´m hooking the timing lamp also...

Thanks both, I´m configuring data cable and PC for the EMM reading, but I´m replacing first the crank (flywheel) sensor this evening (Plug & Pray):p
spark is erratic, some times big bang, other,...

I´m having troubles trying to revive a 1998 150 Ficht Evinrude
no experience with those...:confused:
engine fires like timing is offset, it does not start
pickup pump is fine, spark plugs new,...

Hello::)
What about inside the engine? rule restrictions?:confused:
IF NOT,;): "open" your reed valves stops 1 (one) millimeter all of them, (use plastic reeds)
you must also see how your top...

Ok, I tested the boat today, went all the way down throtles, till 5,600 and no problem at all, no oil alarm, no low pressure alarm, no high temp, or anything, BUT...
now, gauges are beeping about...

Mercguy:
Mercs are: 150 EFI
1.-2002, serial: OT445432
1.-2003, " OT747825

Asked Mercury Marine of Mexico, for wiring diagrams for those engines, (received other model) because the big...

Gracias Pat:
Have to fix some "last minute" boats, prior Holy Week, and didnt even got close the mercs, I have new hoses, maybe in a day or two will have plenty of time to work them.

I did swap ECM´s and reprogramed location, then the gauges, cleaned oil lines, past saturday went to test the boat, and found both fuel lines (mercury grey color) completly degraded, so I couldnt run...

until now, no problems with fuel, both motors are around 20 hours after break in, I sold that boat in 2004, first owner used 3 times in fresh water, then sold it to another who launched the boat 1...

:o Will do it right away, Gracias Mi Amigo Fast Fred..:)

Ok Boys;
I have problems with a boat with 2.- 150 EFI MERCS 2002 port, 2003 stbd.
port engine doesn´t go more than 4K rpms, without triggering low oil reservoir alarm (small engine tank) and...