Search:

Type: Posts; User: dave dalton; Keyword(s):

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    2,718

    Over the years of collecting Koings I have had a...

    Over the years of collecting Koings I have had a few of Chucks motors.They are polished inside and outside with their stamp on various parts. have quite a bunch of their stuff now.also some trick...
  2. Replies
    290
    Views
    232,032

    Sticky: To clarify..The red pipes on Glen's # 41 Tunnel...

    To clarify..The red pipes on Glen's # 41 Tunnel 500 green boat
  3. Replies
    290
    Views
    232,032

    Sticky: I still have these pipes...

    I still have these pipes...
  4. Replies
    17
    Views
    8,721

    l have just finished 6 Konig motors that were...

    l have just finished 6 Konig motors that were completely seized or covered in (castor) and the best thing l have found(lnfo from model airplane guys) is Pinesol, amazing stuff!! Use it full strengh...
  5. Replies
    1
    Views
    1,723

    l built one on a Mckreery (sp)( similar to...

    l built one on a Mckreery (sp)( similar to Hustler) tower with modified 302 l/unit and 11/16" propshaft.55846
  6. Replies
    1,501
    Views
    832,986

    Sticky: l have a 12mm brotch & get couplers made out of...

    l have a 12mm brotch & get couplers made out of good round stock steel ( not stainless).too hard will wear out brotch.have had 15 or 20 made. never had a problem. ddalton67@hotmail.com..o.d. is 1...
  7. Replies
    7
    Views
    2,516

    Crank is ' spreading" at pin ,from hi rpm's. 20...

    Crank is ' spreading" at pin ,from hi rpm's. 20 yrs. ago worked on buddys rz350(390cc)
    motor was running up 10,000 rpm's m/c roadracing.It was doing same thing.
    You need to rebuild crank & weld rod...
  8. Replies
    6
    Views
    2,387

    Thanks

    Thanks Jeff,WE got FGP back on CBF program,We now call it CGP
    CLASSIC GRAND PRIX,Have 1966 FB,But realy need to get that VC feeling
    There are other 4 cyl. Konigs lurking about the Ottawa Valley!!!
  9. Replies
    6
    Views
    2,387

    2 parts

    Been looking for a flywheel & guard to fit vc for 2 yrs...PPPPPLEASE...DD
    PM me.
  10. Replies
    37
    Views
    12,475

    bent down stingers

    seems l remember somthing about safety (UIM).aiming down for projectiles escaping.(pieces of pistons,rings or spark plugs.l know l have launched all of these out the pipes!!
  11. Replies
    467
    Views
    120,861

    Another Story

    Hi Glen,Jeff ,Wayne..I"ve been following this thread for a long time now.I tought l should say welcome aboard to Glen & Henk...Been a long time since l seen either one of these guys...Hey...
  12. Thread: 1000 hydro

    by dave dalton
    Replies
    12
    Views
    3,642

    Valleyfield...1983

    JEFF . good to hear from you...l didn't make it out that first heat when it was soooo rough...l got out in heat #2 that was run at about 6 or 7pm.Yes my boat was built from a set of dave's frames. lt...
  13. Thread: 1000 hydro

    by dave dalton
    Replies
    12
    Views
    3,642

    l rememer that..

    l remember that outfit. Valleyfield 1983. Hank won. l was 2nd. l led for 3 laps....almost fell out... thought 2nd was better than swimming...
    tried to post story of that race but lost game to...
  14. Replies
    2
    Views
    1,832

    if it was only that simple...

    this case is very old ...has V cutout in back of casting above propshaft area.
    date on case is 3/69..Brian Hendrick got me a n.o.s. driveshaft last winter from Steve.Brian also has one of these...
  15. Replies
    2
    Views
    1,832

    koing gear set

    looking for gears to fit older 500cc splitcase..15/16 or14/15 lf they would fit.....case is 1970 straightcut press-on gears...thanx.DD
Results 1 to 15 of 17