With all due respect, i don't think you are going to see a lot of "what-to-do-next" in regards to this motor. I, for one, won't elaborate on the things it took me some 10+ years to gather. I am not a...
Type: Posts; User: Phil McDaniel; Keyword(s):
With all due respect, i don't think you are going to see a lot of "what-to-do-next" in regards to this motor. I, for one, won't elaborate on the things it took me some 10+ years to gather. I am not a...
Sorry ya not there yet mr. Ballistic, but jason's right. 8,000+ all day every day and let's go fishing days. All on 87 octain gas. Don't talk down to somebody just you haven't been there and done...
Daren, They are the large wrist pin and other than one(1) casting mark, they are just like the Merc. 2 ring piston. They gram out lighter(2 grams) than the Vertex. Looks like Merc., just cheaper in...
Dave, things are out there to change things up a little. On a 3 cyl. OMC I built, I adapted a 70 Yamaha flywheel and stator to it. Didn't have a 70 pack so I took a 3 cyl. merc pack and changed the...
Randy, From my last order from Pro Marine/Vertex they have plenty now. They were only out of the .015 over's. I know Van Over bought a lot when the shipment finally came in.
I am now placing an...
Take the bowls off and check to see if one or more of the washers which go on the fuel nozzle to seal the bowls from the bodies is missing.--------- sounds like what it might be. Phil
Fred, Clear up your box OR give me a call. Thanks Phil McDaniel 843-446-7767
Forgot to mention the diff. in the cranks. ---Earlier motors had 4 spline cranks as did/does the 49. Then they started with a 17 spline crank. All were forged. I understand from the SST60 guys that...
Ron, Even though the cranks will interchange as well as the carbs and ignition(with a little modification to flywheel for trigger) and also the front half/reeds will fit, the block and head are diff....
I HAVE .020's, .030's &.040's LEFT. I HAVE SOME NEW RODS AND JUST ORDERED 30 SETS OF WRIST PIN BRGS. TODAY( 8/5). MOSTLY 20&40'S THOUGH. DON'T KNOW WHEN THE NEXT ORDER WILL BE IF EVER.
RODS HAVE...
Which 25 are you talking about? 22C.I. or 31.8??
Forgot to post; there are other factors which WILL influence your desired timing.
Points that slip and/or a loose belt will cause a variance (will be negative). Front half/crank case cover bolt...
Mike, The last post was to put your motor IN TIME so as when mag fires it goes where it is suppose to, #1, #2, etc.
Now that we have the motor in time let's move the mag. to get the correct...
Take #1 cyl. to TDC,move arrow on pully to center of crank, put belt on. It's done. Motor will be in time. Has nothing to do with the timing before TDC as to when you want your cyl. to fire. Phil
Always has been the plan with me.---------Smart man Tim.
The pancake flywheel will work on the 49 and 56 motors with the newer style ignition. It will have to be cut on the hub like the SST 60/ fishing 56er to allow the black trigger to clear.
Pistons have been ordered. A special thanks for all those guys who made this happen. Will be in in about 2or 3 weeks and will have some extras available. Hope these will suit most everyones needs....
Hey guys, Lost my sheet of paper as to who needs and wants to get in on the 3-cyl. OMC Mod. 50 type pistons. I have one man who may take enough to make an order. Help me out with your names and...
From the center of the rod(crank end) to the top of the piston port timing is the same on both short and long. As for ferformance:
shorter rods are faster on punch------- with a lot of piston/motor...
As near as I can measure the rods(fish and Mod.50) measure 4.242" +/-. This is from center of crank end to center of wrist pin end.
As for the 56 ci/SST60 rods they are shorter than these above...
Rods:
Back in the 70's when OMC was building the Mod.50 they took a rod that they already manufactured to use for this motor. It was in the 2 cyl. motors in the 50's and 60's and early 70's. The...
Need some more orders to make a run of pistons for 3 cyl. OMC's. Have half enough to order. Let me know as to the size and quantity needed. Phone #'s are in an earlier post. Thanks Phil McDaniel
In Cincinnati, Ohio in 1983 the mod commission met with others to structure what is today the FEH, FER. There was a lot of input from mostly "E" Class drivers. Along with...
All you have to do is find the right piston/wrist pin hole size,,,wrist pin location,,, skirt porting,,,etc.
Which rod are you planning to use????
You know, several years ago OMC and all it's...
Need some more orders for pistons. Spread the word and contact me at Phil McDaniel 843-650-0400 home 843-446-7767 cell or rpms@sccoast.net
Thanks Phil
I have a Mod 50 flywheel which has never had any exterior magnets installed. Any ideas on who put/puts then in service flywheels for OMC/Bomberdiea?? Or maybe someone aftermarket. Haven't checked...
J, Before offering you some info. to help, I need to know 2 things. What type ignition(pack,stator,etc) are you running and where are you from?? Phil
I've been running the same thing Danny's running except I add some molybdenum disulfied. Same gears in a "D" unit since "81 and they haven't even laped in yet. Phil
Seems as there might be enough interest in my pistons to have some more made. If so, I will have to have orders for at least 1/2(50) before I order. My order will consist of .020s, .030s, and .040s...