Search:

Type: Posts; User: HTarver; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    23
    Views
    41,859

    60mercury, Thats pretty Impressive! Yall let us...

    60mercury, Thats pretty Impressive! Yall let us know how this grudge match turns out.
  2. Thread: 3 cyl Merc 40

    by HTarver
    Replies
    259
    Views
    79,947

    Heck yea that sounds good to me! I start my 8...

    Heck yea that sounds good to me! I start my 8 days off thursday evening, holler at me when yall decide what day.
  3. Thread: 3 cyl Merc 40

    by HTarver
    Replies
    259
    Views
    79,947

    I can more than more than vouch for Mike Whites...

    I can more than more than vouch for Mike Whites boat. Mike White is no slouch! His boat is very Fast/Quick for a 15x48 Weldbilt with a tiller handle 40hp! I have been beside him plenty of times and I...
  4. Replies
    81
    Views
    37,158

    Hey buddy, There aint no since in arguing with...

    Hey buddy, There aint no since in arguing with these people anymore. They live in a whole nother country and they think, Race, and setup boats in whole nother way than we do! And above all There is...
  5. Replies
    4
    Views
    17,781

    what is that, a 12x48 you should have no problem...

    what is that, a 12x48 you should have no problem running 45mph wit a STOCK 40hp and the right prop/setup. I run a 13x44 flat bottom like this one with a modified 40 mercury, it runs in the low 70s.
  6. Thread: Timing

    by HTarver
    Replies
    8
    Views
    3,570

    Yea, if you have never messed with changing the...

    Yea, if you have never messed with changing the timing. Cuz stock timing on your motor is 24 degrees.
  7. Thread: Torque Tamer

    by HTarver
    Replies
    3
    Views
    4,182

    What you need to do is, loose the torque tamer...

    What you need to do is, loose the torque tamer then Tie a couple rubber bungee cords from your tiller arm to the back corner of your boat. (the driver side of the boat)
  8. Thread: Torque Tamer

    by HTarver
    Replies
    3
    Views
    4,182

    Yea they work, but it will slow u down.

    Yea they work, but it will slow u down.
  9. Thread: air box

    by HTarver
    Replies
    11
    Views
    5,642

    Ive run these motors ever since the day they were...

    Ive run these motors ever since the day they were built up until now. The first thing I do to a new mercury 3 cylinder 3 carb motor that i get is blow that air box right off the front of the motor...
  10. Replies
    81
    Views
    37,158

    Looks Real Good for a 2 Cylinder

    What I would do is, put a nose cone on it and raise the motor up till the center of the prop shaft is level with the bottom of the boat and you will see more top end. Also a good 6 inch jack plate...
  11. Replies
    8
    Views
    7,769

    Check out Titan Tiller. Its about $1200.

    Check out Titan Tiller. Its about $1200.
  12. Replies
    16
    Views
    6,402

    Heck if ur paying to get it cut just go ahead and...

    Heck if ur paying to get it cut just go ahead and make it a 12 inch. That's what we did.
Results 1 to 12 of 200
Page 1 of 4 1 2 3 4