Search:

Type: Posts; User: rustnrot; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    2,097

    That's very interesting, FastJeff. I think I can...

    That's very interesting, FastJeff. I think I can visualize what is going on here with that cloud and how it is formed.

    Does anyone know of a pictorial showing it?
  2. Thanks, this IS exactly the kind of input I need...

    Thanks, this IS exactly the kind of input I need and makes perfect sense. The Tohatsu already has built in power tilt trim. Both engines are 15 inch shaft.
  3. 13 Foot Dee Vee Hull for Exhibition Racing and General Use Motor Mounting

    I have a Bullet 130, a 13 foot deep vee hull that I am either putting a 50 hp Tohatsu or 60 hp Mercury on it. I need some "which is better" guidance not so much for the motor but rather for the...
  4. You all need to know if you have a TLDI Tohatsu...

    You all need to know if you have a TLDI Tohatsu is replacing air injectors in many motors:

    http://www.tohatsu.com/tech_info/injectorcampaign.html
  5. Replies
    140
    Views
    251,517

    ...But I see 4 spark plugs...

    ...But I see 4 spark plugs...
  6. Replies
    140
    Views
    251,517

    HA! I doubt it, that chip board is there for a...

    HA! I doubt it, that chip board is there for a reason. When it gets wet, it expands, that's why they call it an EXPANSION chamber!
  7. Here is a link about the two different parts...

    Here is a link about the two different parts between the 40 and 50:

    http://www.internetoutboards.com/PartDetail.asp?id=1049

    Also, I noted looking through the parts manual that those are the...
  8. That's why I asked...I thought 50hptiller said...

    That's why I asked...I thought 50hptiller said his had one too. Hopefully he will see this thread.

    I'm willing to bet that the only reason is there is two different part numbers for the 40 and 50...
  9. So as far as you know, your 50 TLDI never came...

    So as far as you know, your 50 TLDI never came with this "washer", it wasn't removed by somebody?

    When your dial caliper cooperates...
  10. Tohatsu 40HP TLDI Throttle Body Same as 50HP? (See Pics)

    I may be installing a replacement 50 HP TLDI computer in a Tohatsu 40 TLDI engine. As you may know the only difference between the 40 TLDI and 50 TLDI is the computer (ECU) itself and also the...
  11. Tohatsu SERVICE Manuals Online for Download pdf Format from Tohatsu Argentina

    Ran across this link today, has alot if not all the Tohatsu service manuals for download in pdf format. Even though this is hosted via Tohatsu Argentina the manuals are in English.
    ...
  12. 1995 Mercury 40HP 4 cylinder Oil Pump Removal

    I have a 4 cylinder 44 cu inch Merc I want to remove the oil injection system from. There is an oil pump at the bottom of the block.

    Should I:

    1. Remove the driven (worm) gear and put the now...
  13. I carefully marked the shafts and checked. The...

    I carefully marked the shafts and checked. The 1989s (actually have two) both measure for the 1.83 ratio, the 1977 is a 1.64. I did see a mention of both these ratios in a Merc book. And there is...
  14. Not familiar with the "blue band" moniker. What...

    Not familiar with the "blue band" moniker. What years does this represent?

    I measured the studs -- they are the same distance apart.

    Now, does anyone know about parts interchangeability -- to...
  15. Mercury 40, 50, 60, 70 HP Drive Shaft Compatibility 1977 and 1989 Models

    I have two lower units. One a 1977 on the left and a 1989 on the right. The 1989 has a short shaft and the 1977 is long shaft. The 1977 is off a 70 HP 3 cyl but would also be the lower unit for 3...
  16. Ok, this is going back together now, honed with...

    Ok, this is going back together now, honed with new std size pistons. Block assembly has begun.

    Carbs rebuilt, top had #74 jet, bottom #72, does this sound like it should?

    FastJeff, I saw...
  17. I figured inflatables, thanks. And I know it is...

    I figured inflatables, thanks. And I know it is a regular motor.

    I'll break it down. At least the bolts remove easily enough.
  18. Mercury 60HP American Outboard Federation Motor Project

    Here are some pics of a recent motor I could not pass up that obviously has raced before. I need some advice from this fine forum.

    1. What is (was) the American Outboard Motor Federation
    2. What...
  19. The props on the wall -- Harry Schoell's that fit...

    The props on the wall -- Harry Schoell's that fit Pulse Drive surface drives.

    So -- is it OK to go with the 20" transom?

    French Phil -- do you mean if the motor is still too low go with a...
  20. Tohatsu 40 TLDI -- 13' Deep Vee Runabout Propping

    I am in the process of a build of this 13' (12' 8" 20 deg deep vee hull), called a Bullet 130 made in NJ in the 1980's. At present, I have a short shaft Nissan Tohatsu 40 hp tldi with power trim...
Results 1 to 20 of 30