Search:

Type: Posts; User: smitherik33; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    2,789

    Bump, I'll take $205 for it.

    Bump, I'll take $205 for it.
  2. Replies
    1
    Views
    2,789

    31.8ci OMC 30HP Conversion Parts

    I have a 30/35 hp carb and intake for sale. The most cost effective and simple way to get more out of your 25hp Johnson/Evinrude. The price is $250 shipped within the US. (FYI, the previous owner...
  3. Replies
    0
    Views
    2,565

    59ci Mercury Carburetor Spacer Kits

    59" Mercury 3/4" carburetor spacer kits. $110 shipped. The first picture on this post is a display of what comes in the kit. (3 spacers, 3 new gaskets, 1 heat resistant HDPE throttle roller wheel, 3...
  4. My apologies, completely forgot to include the...

    My apologies, completely forgot to include the price. $75 shipped within the US.
  5. 59"ci (40/50/60) Mercury tiller handle spacer

    This kit is for those that don't already have a big tiller and would like to extend your stock tiller handle without having to add an extension onto the handle itself. This spacer is made from 1X3...
  6. 40/50/60hp 59ci mercury intake manifold spacer

    I still have a few of these left if anyone is interested in one. They are cut from 3/16 aluminum plate and go between your manifold and reed plate (not between your reed plate and front half) 74718
  7. Replies
    91
    Views
    103,043

    I'm just curious if this can be done with one...

    I'm just curious if this can be done with one carburetor? If so, I'm pretty confident that I can design/fabricate a similar v block set up.
  8. Thank you, I see it now

    Thank you, I see it now
  9. Having trouble finding it. If you have a link...

    Having trouble finding it. If you have a link handy I'll take a look at it. Sounds logical though. There's probably some motors that benefit from it and some that don't.
  10. Hightide, I agree with your train of thought. I...

    Hightide, I agree with your train of thought. I also think people get intake volume and crank case volume confused. On a separate post a guy tried telling me that I was decreasing crankcase pressure....
  11. Guys I think a few of you are going a little on...

    Guys I think a few of you are going a little on the extreme side. 3 inches is obviously way too much of a volume increase. That just sounds like a bad idea, thats why I only went 3/16. I have...
  12. Increasing Intake manifold volume on a 59ci mercury

    I apologize if this is being posted twice. I don't think my initial post uploaded.

    Does anyone know if increasing intake manifold volume is beneficial? I recently designed and installed a 3/16"...
  13. Increasing Intake manifold volume on a 59ci mercury

    Good morning everyone,

    I recently developed a 3/16" intake manifold spacer for my 59ci mercury in hope of allowing the intake to flow better. I chose to use a thin piece of material (3/16")...
  14. Replies
    5
    Views
    6,629

    Thanks for the responses, gents

    Thanks for the responses, gents
  15. Replies
    5
    Views
    6,629

    13 spline mercury chopper 2 18p

    anyone have an 18p 13 spline mercury chopper 2 or 1 they want to sell? Any feedback on them? Which is better 74209
  16. Replies
    1
    Views
    2,514

    31.8 ci thin head gasket

    Does anyone know where I can find the thinner/higher compression head gasket for a 30hp evinrude? I know they exist, but can't seem to locate one. Thanks for reading!
  17. Replies
    3
    Views
    13,861

    59ci Mercury modified Reed plate

    Hello, I am wondering if anyone on here has modified their Reed plate on a 59ci mercury. If so, were there any noticeable gains? It seems as if there is some improvement to be made with this design.
  18. Replies
    91
    Views
    103,043

    Good evening. I have recently acquired a 1982...

    Good evening. I have recently acquired a 1982 head as well. I'm wondering if I'll gain any compression just by simply by bolting it on. Did you use a certain head gasket? I've heard of a thinner...
  19. V block Reed plate for 3 cyl 40hp mercury.

    Do y'all know anyone that makes a v block Reed plate for these motors? I've heard of it being done but never seen it in person. I've also heard of modifying the stock Reed plate. If anyone has had...
  20. Thank you for the reply. I haven't put mine on...

    Thank you for the reply. I haven't put mine on yet, but I've been told that a lot of the new head gaskets are "low compression" gaskets and are thicker than the ones from 82. I don't remember the...
  21. 35hp Evinrude High Compression Head question

    I believe I found a high compression head from a 1982 35hp evinrude on Ebay and went ahead and bought it. Looks like it has the almost 360 degree squish band that its supposed to have. Can I bolt...
  22. Replies
    91
    Views
    103,043

    Did your cleaver slip like hell when trying to...

    Did your cleaver slip like hell when trying to plane the boat off. All mine does is slip and the motor goes up to like 5000rpms and I've gotta practically run to the front of the boat to get it to...
  23. V block reed valve setup for 31.8ci Johnson/ Evinrude

    I'm interested in doing away with the flat/petal style reed setup on my 31.8ci powerhead. Does anyone have any experience in fabricating a v block reed setup for these motors?
  24. Replies
    91
    Views
    103,043

    Has anyone on here ever fabricated a V block reed...

    Has anyone on here ever fabricated a V block reed set-up for the 31.8ci?
  25. Replies
    4
    Views
    9,085

    What did you use to block off the the top few...

    What did you use to block off the the top few water inlets? And did it hold?
  26. Replies
    91
    Views
    103,043

    Just curious as to how long that motor lasted...

    Just curious as to how long that motor lasted with all the mods you listed? Have a ron hill 10.25X16 thru hub semi cleaver on it's way to me. Sure hope I can turn it.
Results 1 to 26 of 26