Search:

Type: Posts; User: baldad45; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    622
    Views
    1,171,507

    Sticky: Same rods as a stock 115-150 inline .

    Same rods as a stock 115-150 inline .
  2. Replies
    622
    Views
    1,171,507

    Sticky: Every part of this project has been a masters...

    Every part of this project has been a masters professional quality , from the initial drawings to the final engine and hull covers . To take these mental images of a project and turn them into real...
  3. How did this version run compared to the two carb...

    How did this version run compared to the two carb version you built 1st ?
  4. The homemade triple carbed Merc 700.Thanks Glen

    The homemade triple carbed Merc 700.Thanks Glen
  5. Can you post more pics and details of the intake...

    Can you post more pics and details of the intake setup of the 650's in the pics above ? Thanks Glen
  6. Replies
    622
    Views
    1,171,507

    Sticky: As usual very impressive , I'm waiting to see...

    As usual very impressive , I'm waiting to see your main bearing solution . Final assembly must be in sight now. Glen
  7. They will fit no problem , it's the tuner thats...

    They will fit no problem , it's the tuner thats different . On the T2 cly 1-2-3 use one side and dump straight into the housing . Cly 4-5-6 dump on the other side into a tuner that extends into the...
  8. If it's pre-72 you need a 1250SBP housing , if...

    If it's pre-72 you need a 1250SBP housing , if it's later a T2 will bolt up ,but the tuner is built in and is setup for the different crank only the T2-T2X have.
  9. Replies
    1
    Views
    2,518

    I believe there is a factory kit for the later...

    I believe there is a factory kit for the later inlines...
  10. Replies
    6
    Views
    6,266

    I think if it's a 650XS this is a great deal ,...

    I think if it's a 650XS this is a great deal , but for everyday use on a Jon boat not a good choice . Not sure they were made in 74 , they were listed in 76 advertising . You wouldn't have any...
  11. Replies
    622
    Views
    1,171,507

    Sticky: I think there are three heads that have two...

    I think there are three heads that have two chambers each . Likely much easier to cast 3 smaller heads than to pattern and cast a large single head . See post #45 ,jigging for a 6 cylinder would have...
  12. Replies
    10
    Views
    4,911

    http://i49.tinypic.com/30xjsly.jpg,http://i46.tiny...

    http://i49.tinypic.com/30xjsly.jpg,http://i46.tinypic.com/mkw2oi.jpg, Thanks for the advice ,its much better now and undetectable running your finger over it . Glen
  13. Replies
    10
    Views
    4,911

    I know what your describeing and that crossed my...

    I know what your describeing and that crossed my mind, but I think I need to flateen out the ripples 1st to minimize the loss of metal . I think the sharper the blade the better as long as it can...
  14. Replies
    10
    Views
    4,911

    Thanks ,thats what I was thinking, except for the...

    Thanks ,thats what I was thinking, except for the details . Glen
  15. Replies
    10
    Views
    4,911

    picshttp://i46.tinypic.com/34zczs1.jpg,http://i48....

    picshttp://i46.tinypic.com/34zczs1.jpg,http://i48.tinypic.com/jpfozn.jpg,http://i45.tinypic.com/funfbn.jpg,http://i49.tinypic.com/mrqphh.jpg. Very difficult to get a good pic ,also very small. I was...
  16. Replies
    10
    Views
    4,911

    Cleaning up the leading edge of SS cleaver

    I have a cleaver with 2 blades perfect and the 3rd blade has small ripples for an inch in the middle of the leading edge . What is the best way to true up this edge ,you can barely see it, but is...
  17. Replies
    622
    Views
    1,171,507

    Sticky: Simply amazing, just to draft this design , then...

    Simply amazing, just to draft this design , then to pattern it , cast it , and finally machine and assemble it . Details ,details, my hats off to you ! The patience ,skills ,and knowledge to...
  18. Replies
    1
    Views
    2,846

    No power port on 135 and the 72 140 , the 72 140...

    No power port on 135 and the 72 140 , the 72 140 was the same as 150 except it didn't have power ports , So 10 HP. at the powerhead is the answer you're looking for.
  19. Replies
    3
    Views
    3,321

    I6

    Not a lot you can easily do to a I-6 .what model do you have ?
  20. Replies
    5
    Views
    6,302

    Arne the port itself will not be a problem , but...

    Arne the port itself will not be a problem , but the bevel on the piston edge above the port will change the port timing of the center port allowing it to open to soon. Glen :D:)
  21. Replies
    866
    Views
    828,203

    Finger ports

    Are the pictures still available from posts 312.313.320-323 in the original thread .It says allyoucanupload by webshots is down for maintenance . Week later still the same ,any chance of getting...
  22. Replies
    24
    Views
    13,253

    T-ll setup

    Thanks Guy for the responce , I used avgas in the past but its getting hard to get legally. I used to just drive out to the airport and get 100 gal. ,a few years ago they wouldn't even sell me 5...
  23. Replies
    24
    Views
    13,253

    T-llX Timing and jetting

    Just wondering what timming and jetting you were running before and what you changed too ?Which carbs are you using TC-3A or TC-3B ? I have a T-ll that I haven't run in ten years that I want to get...
Results 1 to 23 of 25