Search:

Type: Posts; User: tunnelvision07; Keyword(s):

Search: Search took 0.00 seconds.

  1. this project is coming along slowly but here are...

    this project is coming along slowly but here are a few updated pics of what I have done so far.

    60575
    60576
    60576
    60576
  2. motor, lower unit, and composites suggestions

    I have been looking for a boat with a bottom similar to the Allison or critchfield to convert over to a bay/flats boat. I found a 1979 15' hydra sport bass boat the other day with a pad. The boat...
  3. Replies
    5
    Views
    2,881

    Yes it was working fine yesterday. And cranked up...

    Yes it was working fine yesterday. And cranked up and ran fine today for a minute or so then shut off like the key had been turned off. The engine still will not start if I disconnect the black and...
  4. Replies
    5
    Views
    2,881

    1977 75 hp Evinrude won't start

    I disconnected the black and yellow wire and now it will start. So I replaced the key switch and it's still doing the same thing. What to check now or other possible solution.
  5. "Yamaha 40/50 from yrs. 85 to 94 . The distance...

    "Yamaha 40/50 from yrs. 85 to 94 . The distance center's top to lower mount's are the same.
    The length's differ from lower mount down of midsection's. " so the long shaft trim units can be used. ...
  6. Replies
    11
    Views
    4,210

    http://www.screamandfly.com/showthread.php?251915-...

    http://www.screamandfly.com/showthread.php?251915-glastron-gt150&highlight=glastron+gt150

    sorry i posted the wrong link here is the correct one hopefully.
  7. Replies
    11
    Views
    4,210

    http://www.screamandfly.com/showthread.php?261692-...

    http://www.screamandfly.com/showthread.php?261692-Glastron-Gt-150-to-add-a-pad-or-not-to-add-a-pad

    here is a link of a gt 150 project. the guy is doing a great job. i think i am going to make a...
  8. Replies
    11
    Views
    4,210

    here is the boat now. just took the rotten floor...

    here is the boat now. just took the rotten floor out might try to take the cap off this coming weekend.
    52444524455244652447
  9. Replies
    11
    Views
    4,210

    thanks guys! i was thinking about trying to do it...

    thanks guys! i was thinking about trying to do it like the hydrostream viper's hull. should i try to add a cut out/ step in the back of the hull like the viper or just all the way to the back of...
  10. Replies
    11
    Views
    4,210

    To add a pad or not to add a pad?

    whats everyones take on adding a pad to a 1977 glastron gt 150? i just got the boat and im going to restore it but was thinking about adding a pad. Has anyone ever done this to this boat? Is it...
  11. how to retro fit a yamaha pro50 power trim unit on a Erude 75hp short shaft?

    what type of moddifications are needed to make this work? pics would be great if anyone has any. i hear its pretty simple. i ordered a trim unit and it should be here tomorrow. im hoping to get my...
  12. Replies
    29
    Views
    5,097

    so you use the 2.4 midsection and lower unit?

    so you use the 2.4 midsection and lower unit?
  13. Replies
    29
    Views
    5,097

    does anyone have a picture of a complete motor...

    does anyone have a picture of a complete motor built like this. i would like to see one. it sounds very interresting.
  14. Replies
    3
    Views
    1,685

    ok thanks, i knew y'all would have a simple...

    ok thanks, i knew y'all would have a simple solution for me. what exactly does the thrust washer do? im running 12.5x23 cleaver without the thrust washer is that going to harm anything? whats the...
  15. Replies
    3
    Views
    1,685

    v4 omc cleaver on a 3cyl omc?

    can a v4 cleaver be made to work on the omc 3 cylinder small gear case "nitro gear case". i know the the prop would have to be cut down but the the shaft size is a little different too. is there a...
  16. Replies
    1
    Views
    1,002

    i asked this question about a 75hp evinrude on an...

    i asked this question about a 75hp evinrude on an earlier thread and fastfred and bill gohr gave some pretty good tips on how and where to do this. im not sure if the 65 block is exactly the same but...
  17. Replies
    4
    Views
    1,794

    thanks for the help! i'll keep yall posted on...

    thanks for the help! i'll keep yall posted on what i find out.
  18. Replies
    4
    Views
    1,794

    this motor actually doesnt have a safety cord it...

    this motor actually doesnt have a safety cord it just has a key. That was a bad example on my part, i apologize. can this happen with the keyswitch too?
  19. Replies
    4
    Views
    1,794

    no spark evinrude 75hp

    The other day i was in my boat and my motor was running fine. then today when i tried to take off it just shut off like the the safety shut off cord was pulled. I started it back up and it did fine...
  20. Thanks for the help. I appreciate it!

    Thanks for the help. I appreciate it!
  21. Safe rpm at WOT with a stock Evinrude 75hp

    What's the most rpm's I should run with a stock 75hp Evinrude so I don't blow it up? The only mods are drilled lower unit and hustler exhaust. It's on a 12' tunnel hull
  22. I havent ran the boat yet im still putting...

    I havent ran the boat yet im still putting everything together. how are yall running them, with or without thermostats? what brand/type of reeds should i run? its all stock except for the hustler...
  23. Thanks for the pictures and details Fast Fred and...

    Thanks for the pictures and details Fast Fred and Bill Gohr. I'm waiting for my pressure guage kit to come in then I will post pics of finished product. Thanks again!
  24. thanks for all replys and explaining on the...

    thanks for all replys and explaining on the different circumstances guys! were you able to find pictures fast fred? bill gohr are you talking about the flat spot on top of the block, left of the...
  25. Installing a water pressure gauge on 75hp evinrude?

    Where/how on the block do i install a water pressure guage on a 1977 75hp evinrude with hustler exhaust?
  26. Called and talked to Dave at seaway. Real nice...

    Called and talked to Dave at seaway. Real nice guy. He got me hooked up with what I needed.
  27. okay thanks! I'll probably be giving yall a call...

    okay thanks! I'll probably be giving yall a call to order some beginning of next week.:D
  28. I want to make me a set of sst 60 lower mounts

    Im working on project. and im considering making me a set of solid lower mounts for my 75 hustler. I already have solid uppers. can someone post some pictures of theirs? it would be greatly...
  29. Replies
    140
    Views
    130,770

    Sticky: no problem glad i could help.

    no problem glad i could help.
  30. Replies
    140
    Views
    130,770

    Sticky: Are thes the measurements you want? My exhaust...

    Are thes the measurements you want? My exhaust will bolt to a factory block? I don't think you can get them any more. I tried to find some info by searching the web but I didnt find much. I could...
  31. Replies
    140
    Views
    130,770

    Sticky: sorry for making the pictures so big.

    sorry for making the pictures so big.
  32. Replies
    140
    Views
    130,770

    Sticky: does this plate work good? Its a little different...

    does this plate work good? Its a little different from the others I have seen on here. Can it be bolted to a stock block? I bought this a while back but, I haven't had time to mess with it yet it...
Results 1 to 32 of 49