Search:

Type: Posts; User: Cubman; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    38
    Views
    19,711

    Numbers mean nothing to me. I just want to get...

    Numbers mean nothing to me. I just want to get the best for performance out of what I have, while using it to do what I enjoy doing- fishing and hunting.

    From where I sit I see that we are both...
  2. Replies
    38
    Views
    19,711

    Do you have a gas tank or batteries towards the...

    Do you have a gas tank or batteries towards the front of your boat or do you keep all the weight in the back?
  3. Replies
    38
    Views
    19,711

    Cajun, I've got a problem with my jon boat...

    Cajun,

    I've got a problem with my jon boat porpoising. It is a 1648 with 7 degrees V on the bottom. Motor is a 70hp Johnson with 19 pitch omc SST prop. The cavitation plate is 1.5" above the...
  4. Replies
    3
    Views
    4,012

    You may find it here:...

    You may find it here:
    http://www.bbcboards.net/zerothread?id=397772
  5. Replies
    6
    Views
    12,055

    Hooking the hull worked for me. 1/8" on just the...

    Hooking the hull worked for me. 1/8" on just the outside strakes was all it took.
  6. Replies
    38
    Views
    19,711

    Cajun, I have read a post of yours on another...

    Cajun,

    I have read a post of yours on another forum that said a 16' boat will run 3-4mph slower than a 15' boat. What can I do to minimize this? I assume it is mostly the weight distribution?
  7. Replies
    38
    Views
    19,711

    How was the yamaha prop modified to allow you to...

    How was the yamaha prop modified to allow you to go from 3" above to 6" above?
  8. Replies
    38
    Views
    19,711

    Sorry for the elementary question, but if I...

    Sorry for the elementary question, but if I operate in water no less than 3' deep would I be better served to just raise my motor on the transom until I loose water pressure or cavitate?
  9. Replies
    38
    Views
    19,711

    Cajun, Will a jackplate on an aluminum boat do...

    Cajun,

    Will a jackplate on an aluminum boat do much for speed or is it primarily for shallow running? Is there a hub available to run this yamaha prop on a V4 OMC (13 spline, 4.25")?

    Thanks
  10. Replies
    38
    Views
    19,711

    TTT Any more advice on setting up an aluminum...

    TTT

    Any more advice on setting up an aluminum boat? I've got a 1648 with about 7* V on the bottom with a 70hp Johnson tiller. How much setback should I start with? I need to run a prop with a hub...
  11. Thread: 56" omc cooling

    by Cubman
    Replies
    22
    Views
    9,606

    Does anyone know where I can find a copy of the...

    Does anyone know where I can find a copy of the service bulletins mentioned previously?
  12. Replies
    1
    Views
    2,468

    70 carbs on 60 Johnson

    I compared the part numbers between the two motors, the only difference I can find is the carburetors.

    I found these carburetors from a 1990 70hp Johnson. Will they swap on my 1992 60hp Johnson? ...
  13. Replies
    5
    Views
    4,474

    Thanks powerabout. I am not familiar with the...

    Thanks powerabout. I am not familiar with the work pak? Is it an acronym?
  14. Replies
    5
    Views
    4,474

    Thanks Mark. Will I be alright to run it wide...

    Thanks Mark. Will I be alright to run it wide open with a light load for extended periods of time (10-15 minutes), or is running over 5500 not a good idea?
  15. Replies
    5
    Views
    4,474

    Max RPM 1992 Johnson 60hp

    I have a 1992 Johnson 60hp 3-cyl (56ci) J60TTLENE that I need a prop for. Should I pitch to 5500rpm or go higher? I am looking for the best performance without sacrificing reliability. Also, any...
Results 1 to 15 of 37