Search:

Type: Posts; User: Nason; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Thread: carbs

    by Nason
    Replies
    16
    Views
    13,445

    thats what i was trying to figure out, the idle...

    thats what i was trying to figure out, the idle side was good but the top end was slower getting to max rpms. thanks for the reply.
  2. Thread: carbs

    by Nason
    Replies
    16
    Views
    13,445

    The motor is not stock, had a little work done to...

    The motor is not stock, had a little work done to it. So what you are saying is if you have carbs that flow more air you can run the same jet as the carb that flows less air? Just trying to find a...
  3. Thread: carbs

    by Nason
    Replies
    16
    Views
    13,445

    carbs

    Questions for the Guru's

    I understand it takes the right air intake to fuel mixture to gain hp and you also have to be able to exhaust same. Why is it you can take a carb that should have a 62 jet...
  4. Thread: Proper name

    by Nason
    Replies
    3
    Views
    3,180

    Thanks that's the info I was looking for.

    Thanks that's the info I was looking for.
  5. Thread: Proper name

    by Nason
    Replies
    3
    Views
    3,180

    Proper name

    What is the proper name for cable helm steering? I have been looking for the cable helm steering but all that shows up is the hydraulic or Teleflex cable steering.Thanks for any help
  6. Thread: merc guys

    by Nason
    Replies
    7
    Views
    3,845

    yes with 10 o/o ethanol

    yes with 10 o/o ethanol
  7. Thread: merc guys

    by Nason
    Replies
    7
    Views
    3,845

    merc guys

    Need help with this problem.
    Changed spark plug, gap was preset at 35 and merc requires 40 gap would this make a difference on reading the spark plug color?

    Ran motor set at 22 degree 62 jets w/...
  8. Replies
    23
    Views
    41,954

    i'll give you a call jason when we have the...

    i'll give you a call jason when we have the location and date
  9. Replies
    23
    Views
    41,954

    I live in raceland. I'll bring a couple of props...

    I live in raceland. I'll bring a couple of props so you can try some
  10. Replies
    23
    Views
    41,954

    60 Mercury I,ll be home in 10 days maybe we can...

    60 Mercury I,ll be home in 10 days maybe we can find a spot where we can make a couple of runs
  11. Thread: 59ci mercury

    by Nason
    Replies
    5
    Views
    6,475

    check the spline on the crank shaft, the 40-50...

    check the spline on the crank shaft, the 40-50 has 13 and the 60 has 11 I believe. Also what year are you talking about ?
  12. Replies
    4
    Views
    2,485

    check the jam nut on the handle it may be too...

    check the jam nut on the handle it may be too tight, check your cable they may have trash or rust in the cover over the cables, check your adjustments if cables are not adjusted properly then it will...
  13. Replies
    21
    Views
    7,204

    Just put a smaller pitch prop and throttle back,...

    Just put a smaller pitch prop and throttle back, you will be able to tell what rpm you are good for when the rev limiter kicks in
  14. Replies
    115
    Views
    27,671

    Mike you been playing with that junk fishing...

    Mike you been playing with that junk fishing prop, You gained .8 mph since last time I drove your boat....
  15. Replies
    115
    Views
    27,671

    sure if you want to

    sure if you want to
  16. Replies
    115
    Views
    27,671

    Pdt you saw the videos what are your thoughts?

    Pdt you saw the videos what are your thoughts?
  17. Replies
    115
    Views
    27,671

    sent 2 videos to pdt if you like post your email...

    sent 2 videos to pdt if you like post your email and I will send them to you also
  18. Replies
    115
    Views
    27,671

    Don't know how to post videos give me a email...

    Don't know how to post videos give me a email address and you can post it.
  19. Replies
    12
    Views
    4,406

    Prop and what does what

    On a fishing prop from the hub to about 1" from the tip of blade (elephant ear tip) what does this control ? Slip?
    On the tip of the blade (elephant ear part) about 1" to center what does tip cup...
  20. Replies
    115
    Views
    27,671

    Guess I am doing good 56.9 / 57 mph on 2...

    Guess I am doing good 56.9 / 57 mph on 2 different gps and 57.3 was the best
  21. Replies
    115
    Views
    27,671

    What would be max speed on 16p, 1.83 gears and...

    What would be max speed on 16p, 1.83 gears and 7400rpms?
  22. Thread: 3 cyl Merc 40

    by Nason
    Replies
    259
    Views
    80,378

    6 pulse

    6 pulse
  23. Thread: 3 cyl Merc 40

    by Nason
    Replies
    259
    Views
    80,378

    Cajun special it sound nice

    Cajun special it sound nice
  24. Thread: 3 cyl Merc 40

    by Nason
    Replies
    259
    Views
    80,378

    do you have a pull start or a electric start. If...

    do you have a pull start or a electric start. If you have electric start , take the gray wire from your regulator connect it to the signal on the tach, take a black wire connect it from battery...
  25. Thread: Too much oil

    by Nason
    Replies
    18
    Views
    7,505

    The motor is a merc 40 hp triple 59 ci that...

    The motor is a merc 40 hp triple 59 ci that has been cut on. The boat is a 15 x 48 weld built, I would like to reach 7500 - 7800 rpms.. The motor is just broken in and I'm trying to fine tune it....
  26. Thread: Too much oil

    by Nason
    Replies
    18
    Views
    7,505

    Too much oil

    Is it possible that too much oil will kill your rpms ?
    I'm trying to set up a new built motor but the rpms are not coming around, the oil i'm using is R50 16 oz to 5 gallons gas. I tried this...
  27. Replies
    6
    Views
    7,423

    I've got a 2004 59ci and it has 120 psi

    I've got a 2004 59ci and it has 120 psi
  28. Replies
    36
    Views
    11,730

    I got the same prop,except it was tried on a 40...

    I got the same prop,except it was tried on a 40 Mercury,42 mph was the fastest it would go. Slapped on a 3 blade power tec 10-3/8 x 15p fishing prop 45.2, slapped on a 10-3/8 x 18p mercury chopper...
  29. Replies
    11
    Views
    11,535

    I removed the tab that was installed after...

    I removed the tab that was installed after removing some of the cup on the tab, straighten the tab alittle at a time then just cut it off and gained back the 3 mph. The motor was jacked up with a...
  30. Replies
    11
    Views
    11,535

    THE torque tab does help but I can tell you when...

    THE torque tab does help but I can tell you when I had 1 installed on a 40 merc I lost 3 mph
  31. Thread: Testing stator

    by Nason
    Replies
    0
    Views
    2,063

    Testing stator

    Tested stator on 2005 40 merc 2 stroke triple
    I ran a cdm(511973nl) with a flute attached to the the top coil then repeated for all 3 cylinders as following
    top cylinder 1000rpm = 299 6600...
  32. Replies
    12
    Views
    9,979

    What is the dia and rpms ?

    What is the dia and rpms ?
  33. Replies
    5
    Views
    2,526

    Thats what its doing but its a steady bounce on...

    Thats what its doing but its a steady bounce on the left side. I'll call you tuesday i keep the cell phone off out here in the gulf
  34. Replies
    5
    Views
    2,526

    Boat is 15 x 48 v weldbilt and the motor is a 40...

    Boat is 15 x 48 v weldbilt and the motor is a 40 hp merc with a little work done to it. Boat jumps up with no problem with a 10-3/8 x 18p chopper, also with a 11 x 15p fishing prop but i run out of...
  35. Replies
    5
    Views
    2,526

    Port to starboard

    If a motor is off center by 1/4 inch on the transom, would this make a boat want to bounce port to starboard at mid range speed or could it be from motor being to high on transom?
    At full throttle...
  36. Replies
    23
    Views
    41,954

    shooting for 70-75mph

    shooting for 70-75mph
  37. Thread: Timing

    by Nason
    Replies
    8
    Views
    3,581

    Changed out the fly wheel key but it looked good,...

    Changed out the fly wheel key but it looked good, checked timing still not showing numbers. Accidently touched second CDM and Bam got lite up. Changed out the CDM and the numbers are back to...
  38. Thread: Timing

    by Nason
    Replies
    8
    Views
    3,581

    Thanks for the info, tomorrow I will give it a...

    Thanks for the info, tomorrow I will give it a try.
  39. Thread: Timing

    by Nason
    Replies
    8
    Views
    3,581

    Thanks for the info. The motor is a 2005 40hp...

    Thanks for the info. The motor is a 2005 40hp mercury 2 stroke 3 cyclinder. I tried 2 different fly wheels and both of the the lines/ number at idle you can see the numbers then they disapear then...
  40. Thread: Timing

    by Nason
    Replies
    8
    Views
    3,581

    Timing

    What would cause the numbers to appear then disappear then re appear when you are trying to check the timing? Its not the timing light we checked it on 2 other motors. The motor runs good wot not...
  41. Thread: Torque Tamer

    by Nason
    Replies
    3
    Views
    4,223

    Your right lost 3.6 mph , straighten it out some...

    Your right lost 3.6 mph , straighten it out some gained back 2mph now I have to find the other 1.6 plus hopefully some more
  42. Thread: Torque Tamer

    by Nason
    Replies
    3
    Views
    4,223

    Torque Tamer

    Has anyone ever used a Bobs Torque Tamer and does it really work?
  43. Thread: props

    by Nason
    Replies
    5
    Views
    2,680

    500125001350014500155001650017

    500125001350014500155001650017
  44. Thread: props

    by Nason
    Replies
    5
    Views
    2,680

    Here are some pictures of my boat ...

    Here are some pictures of my boat

    5000350004500055000650007
  45. Thread: props

    by Nason
    Replies
    5
    Views
    2,680

    props

    If you are looking for bow lift, would a 4 blade be better ? I now can run my motor with the prop shaft even with the bottom of the boat,but cannot get the bow out the water to turn up the rpms.Any...
  46. Thread: Best Reeds

    by Nason
    Replies
    10
    Views
    10,898

    Best Reeds

    I just blew a set of Chris Carsons reeds after maybe total of 4 hrs since installed. Would would be the best reeds to install ?
    Thanks for any help.
  47. Replies
    2
    Views
    2,291

    its a plastic hub thanks for the info

    its a plastic hub
    thanks for the info
  48. Thread: Bogalusa guys

    by Nason
    Replies
    6
    Views
    2,452

    in a sharp turn I trim down but it stays on the...

    in a sharp turn I trim down but it stays on the pad,
  49. Thread: Bogalusa guys

    by Nason
    Replies
    6
    Views
    2,452

    traveling sideways across a bayou and back is not...

    traveling sideways across a bayou and back is not a joke, it does hurt the ribs.
  50. Thread: Bogalusa guys

    by Nason
    Replies
    6
    Views
    2,452

    Not scared to go , just not too sure about...

    Not scared to go , just not too sure about handling the boat yet.Need more driving time. Ever since she broke loose on me I have not been able to trim up as high.
Results 1 to 50 of 104
Page 1 of 3 1 2 3