Thread: Building A looper Beast

  1. #261
    Team Member Gene East's Avatar
    Join Date
    Dec 2004
    Location
    Quincy, IL
    Posts
    593
    Post Thanks / Like

    Default

    Quote Originally Posted by BJuby View Post
    Awesome awesome pictures. I have to say I think that is the first time I have seen the electrical system setup (in the boat) from back then. Definitely interesting.
    Welcome to the past glory day of boat racing!

  2. #262
    Team Member Master Oil Racing Team's Avatar
    Join Date
    Jan 2005
    Location
    Sandia, Texas
    Posts
    3,831
    Post Thanks / Like

    Default

    The battery or batteries look kind of like an aircraft battery we once tried on our B hydro. See the tall vent caps. The vent caps in the one we tried had "floating" lead in them that would fall down and seal the vent holes if you go upside down.



  3. #263
    Team Member
    Join Date
    Apr 2005
    Posts
    238
    Post Thanks / Like

    Default

    Quote Originally Posted by Fastjeff57 View Post
    My buddy talked me into putting the starter solenoid in the boat (vs. on the PH). Makes for a lot less clutter and, since often switch engines, I only need one solenoid. Never seen the coil mounted there, however; I like that!

    Jeff
    Jeff, The coil mounting back then was normal to be in the boat as we used one coil and box to run maybe thre or four motors on same boat. It was cheaper to do that way, Plus it reduced the clutter on the engine when you had to work on it or make a parts change, That process too was faster having the box and coil in boat. Steve

  4. #264
    Team Member R Austin's Avatar
    Join Date
    Aug 2005
    Location
    ludington Michigan
    Posts
    248
    Post Thanks / Like

    Default

    Just a few more assembly photos. One picture just drilling the exhaust elbow for water discharge on to the elbow.


    Name:  20140405_121207.jpg
Views: 1199
Size:  168.3 KBName:  20140415_180234.jpg
Views: 1132
Size:  170.9 KBName:  20140415_180258.jpg
Views: 1153
Size:  174.9 KBName:  20140415_181916.jpg
Views: 1117
Size:  90.4 KBName:  20140415_183152.jpg
Views: 1135
Size:  130.6 KBName:  20140415_181958.jpg
Views: 1191
Size:  92.4 KBName:  20140405_123928.jpg
Views: 1109
Size:  175.6 KBName:  20140405_140542.jpg
Views: 1139
Size:  172.2 KBName:  20140405_140557.jpg
Views: 1124
Size:  165.9 KBName:  20140405_144938.jpg
Views: 1120
Size:  127.9 KB

  5. #265
    Sam Cullis Mark75H's Avatar
    Join Date
    Nov 2004
    Location
    Annapolis, MD USA
    Posts
    1,795
    Post Thanks / Like

    Default

    Quote Originally Posted by R Austin View Post
    The unit was purchased new from Mercury in 1970 or 71. I bought 2 left hand units that I was going to use on the rotary valve motors that I was working on. This one ran maybe 8-10 laps. The other is still hanging on the wall untouched as it came from Mercury. Paid 620.00 a piece back then. They are twin pinions. That is why I am using it on the 100 inch motor.

    Merc stopped using left hand twin pinion SSM's at about 140hp because of reliability problems. RH twin pinion units are stronger because the prop shaft gears are closer to the bearings. Later high hp inlines that needed LH props were fitted to turn the powerhead CCW on SSM's that had the prop shaft gears outside the pinions. There was a kit with a reversed starter and special linkage to rack the distributor the other direction with throttle advance.

    I'm pretty sure you will be able to break a left hand unit with this powerhead
    Since 1925, about 150 different racing outboards have been made.


  6. #266
    Team Member
    Join Date
    Sep 2008
    Location
    Singapore/Melbourne/Italy
    Posts
    780
    Post Thanks / Like

    Default

    200 xs ssm 6 is right in and left out if you want to go new.
    Use a v6 race flywheel and starter and run the engine ccw?

  7. #267
    Team Member R Austin's Avatar
    Join Date
    Aug 2005
    Location
    ludington Michigan
    Posts
    248
    Post Thanks / Like

    Default

    Quote Originally Posted by Mark75H View Post
    Merc stopped using left hand twin pinion SSM's at about 140hp because of reliability problems. RH twin pinion units are stronger because the prop shaft gears are closer to the bearings. Later high hp inlines that needed LH props were fitted to turn the powerhead CCW on SSM's that had the prop shaft gears outside the pinions. There was a kit with a reversed starter and special linkage to rack the distributor the other direction with throttle advance.

    I'm pretty sure you will be able to break a left hand unit with this powerhead
    I understand the dynamics of the failure of the units, however they most likely failed because of there application.

    In 1963, a friend of mine and I decided that we would build a racing motor from what parts we could scrounge up. Not being able to afford a lower unit, we decided to make our own. I made some sketches and bought some aluminum and ask my dad what he thought. He thought we were nuts, but he took on most of the project, carving it out with a drill press for a mill and a band saw and a lot of hand cutting and filing. That was my part. The unit pictured on the ground in front of my dads knees, would go about 50 to 100 feet and destroy the gears. We were at Sandford (Midland) Mi. race site looking at yet another set of destroyed gears trying to figure out why. We had used gears from an old 10-15HP Evinrude and reversed the pinion and prop shaft gears to make it on overdrive unit. Sound like couple of green kids?.. We were, and as luck would have it, this was a big race and some big names were there. Could have been the NOA Nationals, did not mean much to me then. I know Hugh Enthroup was there.

    As would be expected, the word went through the pits that a couple of kids were trying to put together an engine to run on there homebuilt Hal Kelly Ben Hur. AND they had built a gear case for it and it kept eating gears. As we were looking over the gears on that blanket, a gentleman came over and starting looking at the parts and pieces with us. He introduced himself as Pop Hubblell. Well, he explained to us that not all gears thrust away from each other. It seams that the gears we were using were spiral bevel and they pull each other together. We turned the thrust bearings around and that unit ran for a few years after that and is still hanging on the wall with the 35HP Evinrude power head that we finally used on it. It ran on a local lake for fun on a Hal Kelly Buzzard hydro. With the over drive gearing. That is still in running condition.

    With all that said, Mr. Hubblell also shared some other knowledge. That was, you never use a prop larger (pitch and diameter) than the unit was designed for. You could turn it, RPM, as fast as you want, but if you over loaded it with a large prop and low RPM HP (torque) it is going to fail.

    I have always thought that that made good sense. My unit will only be pushing 550-600 pounds, plus driver. I will only use a prop of 17-18 inches of pitch and no more that 10 inch in diameter. And if Jennings is right the engine with its stroke will only be good to 9000 RPM. If you use all those numbers and the fact that the totally airborne hydro can reach 95+% prop efficient. I think that puts it some where between 135-150 MPH. That's plenty for playing and not hurt the unit.


    Name:  slides 057.jpg
Views: 1030
Size:  164.6 KBName:  slides 061.jpg
Views: 1025
Size:  107.4 KBName:  20140405_182602.jpg
Views: 1002
Size:  137.0 KBName:  20140405_174651.jpg
Views: 1033
Size:  263.2 KBName:  20140405_174704.jpg
Views: 1005
Size:  266.9 KBName:  20140406_164107.jpg
Views: 1037
Size:  299.8 KBName:  20140406_164122.jpg
Views: 1076
Size:  278.6 KB

  8. #268
    Administrator Aeroliner's Avatar
    Join Date
    Mar 2008
    Location
    Lake Charles, Louisiana 70611
    Posts
    212
    Post Thanks / Like

    Default Looper

    Simply outstanding! What a project. Getting close to first fire in the hole.

    Alan

  9. #269
    Team Member Gene East's Avatar
    Join Date
    Dec 2004
    Location
    Quincy, IL
    Posts
    593
    Post Thanks / Like

    Default

    Looking good, I've got tears in my eyes!

    Great picture of your Dad!

  10. #270
    Team Member
    Join Date
    Nov 2008
    Location
    Horseshoe Bend, ID
    Posts
    657
    Post Thanks / Like

    Default

    Ohhhh wow! You've got to love it! BTW: Great story about the gearcase.

    Tim

Thread Information

Users Browsing this Thread

There are currently 20 users browsing this thread. (0 members and 20 guests)

Similar Threads

  1. Legendary Dub Parker's B Looper found!
    By Original Looper 1 in forum Outboard Racing History
    Replies: 6
    Last Post: 07-25-2022, 06:16 PM
  2. Quincy Looper Pictures and Collections
    By Original Looper 1 in forum Outboard Racing History
    Replies: 71
    Last Post: 01-21-2008, 04:26 PM
  3. Waldman F 44 Looper has been found!
    By Original Looper 1 in forum Outboard Racing History
    Replies: 26
    Last Post: 06-18-2007, 09:55 AM
  4. Quincy's 90 ci King Looper Beast
    By Original Looper 1 in forum Outboard Racing History
    Replies: 1
    Last Post: 04-06-2007, 07:08 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •