Page 3 of 38 FirstFirst 123456789101112131415161718192021222324252627 ... LastLast
Results 21 to 30 of 371

Thread: Johnson "70mod"

  1. #21
    Banned
    Join Date
    Nov 2016
    Posts
    289
    Post Thanks / Like

    Default

    are these white plastic cards staying on
    and what is that blue filler

  2. #22
    Team Member hupiveneilija's Avatar
    Join Date
    Oct 2014
    Location
    Finland
    Posts
    263
    Post Thanks / Like

    Default

    Yes they stay, are between reedstops and frontpiece. Dont go anywhere.
    Blue thing is marine epoxy. Same stuff on the crankcase.

  3. #23
    Team Member hupiveneilija's Avatar
    Join Date
    Oct 2014
    Location
    Finland
    Posts
    263
    Post Thanks / Like

    Default

    What about egt meter for a tuning aid? Any help with that. And is there some target temp to aim or is it dependable for the mods i have made?

  4. #24
    Banned
    Join Date
    Nov 2016
    Posts
    289
    Post Thanks / Like

    Default

    temp needs to be 140 ish if its too low its going to wear out fast. the 56 usually keeps good temp as long as good thermostat is in the motor.

    DO NOT RUN WITHOUT THERMOSTAT.

  5. #25
    Team Member hupiveneilija's Avatar
    Join Date
    Oct 2014
    Location
    Finland
    Posts
    263
    Post Thanks / Like

    Default

    Egt; ExhaustGasTemperature!

  6. #26
    Team Member LittleCharger's Avatar
    Join Date
    Mar 2011
    Location
    London,ON,Canada
    Posts
    160
    Post Thanks / Like

    Default

    Quote Originally Posted by hupiveneilija View Post
    Egt; ExhaustGasTemperature!
    I'll quote Dave Bush on this one

    "Pyros are a good reference tool

    Yes and no. Most likely it will be dead before you see any temp changes even with fast pyros if bad detonation is happening. Temps usually drop a little then it dies. Sometimes you see a slow rise then the drop... Bottom line we have found when lake testing you have to take the time to do it the old fashion way and look at the piston tops and spark plugs period. A few minutes here saves thousands. Forget about the pyro. Pyro placement is a complicated thing in itself. Also, we have found you need a pyro in each cyl. with a fast hertz logging rate to do it right. If you can , do it,it is good info but it wont keep things from blowing up. Only you can. Or if you have det sensing you see it in real time (and if detonation is present) you simply let off the gas, change the fuel or timing and watch the rattle go away..We used to hurt alot of parts when living only by the Pyro. Now we look at it more for reference for cylinder to cylinder mapping. Hope that helps..... "
    Likes hydrospeed77, Powerabout liked this post

  7. #27
    Team Member hupiveneilija's Avatar
    Join Date
    Oct 2014
    Location
    Finland
    Posts
    263
    Post Thanks / Like

    Default

    Thank You LC, just what I wanted to hear.

  8. #28
    Banned
    Join Date
    Nov 2016
    Posts
    289
    Post Thanks / Like

    Default

    will you be putting finger ports in this motor ? if so how will you be doing that.

  9. #29
    Team Member hupiveneilija's Avatar
    Join Date
    Oct 2014
    Location
    Finland
    Posts
    263
    Post Thanks / Like

    Default

    Things go forward. Just use grease to get those needles in place. Foto will show how ive grinded rods to be even. Use old pistons with new rings and honed the sylinders.
    Attached Images Attached Images   

  10. #30
    Banned
    Join Date
    Nov 2016
    Posts
    289
    Post Thanks / Like

    Default

    Was it a flex hone with small balls or 3 leg hone.
    Are you sure the rods are still good at the crank end on the inside ? From pic looks like chrome has worn away.

Thread Information

Users Browsing this Thread

There are currently 3 users browsing this thread. (0 members and 3 guests)

Similar Threads

  1. "Hi Johnson" - Prop Master - Story
    By Tomtall in forum Propellers
    Replies: 5
    Last Post: 06-13-2011, 05:36 AM
  2. Dennis Johnson "Trafficade" Racing
    By Ron Hill in forum Boat Racing Encyclopedia
    Replies: 1
    Last Post: 11-05-2006, 07:26 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •