Thanks Thanks:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 16

Thread: 1975 75 stinger carbs

  1. #1
    Team Member
    Join Date
    Nov 2011
    Posts
    4
    Post Thanks / Like

    Default 1975 75 stinger carbs

    I have a 1975 stinger, my question is the carbs have a threaded hole on the main body of the carb for a jet, one carb has a #30 jet in it. Should all the carbs have that jet, the jet is located where the bowl mates with the upper body. Thanks

  2. #2
    Team Member
    Join Date
    Jul 2011
    Posts
    113
    Post Thanks / Like

    Default

    The 75 had 27s but not sure what was done to your motor over the years. After all, your motor is 43 years old. Are they the right cabs?

  3. #3
    Team Member
    Join Date
    Jul 2011
    Posts
    113
    Post Thanks / Like

    Default

    The 76 carbs had 30s in them

  4. #4
    Team Member
    Join Date
    Nov 2011
    Posts
    4
    Post Thanks / Like

    Default

    I double checked the serial number for the motor, it does show #33 jets for the idle restrictions, but only one carb has it, the other two doesn't have it, there's a hole for it though.

  5. #5
    Team Member hupiveneilija's Avatar
    Join Date
    Oct 2014
    Location
    Finland
    Posts
    263
    Post Thanks / Like

    Default

    Picture would be helpfull for all of us.
    Likes Powerabout liked this post

  6. #6
    Team Member
    Join Date
    Nov 2011
    Posts
    4
    Post Thanks / Like

    Default

    Will try to get a pic later today.

  7. #7
    Team Member
    Join Date
    Nov 2011
    Posts
    4
    Post Thanks / Like

    Default

    Having a problem downloading some pics.

  8. #8
    Team Member
    Join Date
    Dec 2004
    Location
    Lake Lanier (North of Atlanta, Georgia)
    Posts
    54
    Post Thanks / Like

    Default

    Here is a picture of a typical set of 3-cylinder OMC carbs... the top hole is an air idle mixture orifice (air jet) and keep in mind, the bigger the hole, the more AIR is let in for idle... The three plugs are handy to drain the float bowl for long term storage and allow access to the "main orifice" high speed jet in each carb. Buy the correct orifice screw driver online, or carefully grind the sides of a good screwdriver so it fits easily down the hole or you will wreck the jets trying to remove them. The OMC part is 0317002 and also pictured below.
    Attached Images Attached Images   
    Likes crewman060 liked this post

  9. #9
    Team Member
    Join Date
    Nov 2011
    Posts
    4
    Post Thanks / Like

    Default

    Name:  IMG_20180826_204005589_HDR.jpg
Views: 460
Size:  371.2 KB

  10. #10
    Team Member
    Join Date
    Nov 2011
    Posts
    4
    Post Thanks / Like

    Default

    Name:  IMG_20180826_200129946.jpg
Views: 470
Size:  307.3 KB

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 1975
    By racingfan1 in forum APBA PROPELLER MAGAZINES
    Replies: 72
    Last Post: 11-14-2017, 09:46 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •