Thanks Thanks:  0
Results 1 to 4 of 4

Thread: Crank case compression bypass on 2 cylender motor?

  1. #1
    Team Member JohnsonM50's Avatar
    Join Date
    Apr 2005
    Location
    Jersey
    Posts
    1,034
    Post Thanks / Like

    Default Crank case compression bypass on 2 cylender motor?

    Question about an OMC 22ci 25hp I'm looking into adding the reed plate and intake from a 31.8 OMC. The bolt pattern fits so it would seem no problem but there is. Why would there be a bypass on the crank case side of the reed plate? Apparently it isn't on all of them but is on the one I'm working on. Might fill it as the 31.8 reed plate leaves it exposed to outside air. Or, would it be better to fill in a reed plate to cover it like the 22ci one does? Would this bypass be drawing crankcase compression from a decompressing cylinder or forcing compression into a compressing cylinder? Or, just balancing crank case compression? Hell if I know lol.

  2. #2
    Team Member JohnsonM50's Avatar
    Join Date
    Apr 2005
    Location
    Jersey
    Posts
    1,034
    Post Thanks / Like

    Default

    Quote Originally Posted by JohnsonM50 View Post
    Question about an OMC 22ci 25hp I'm looking into adding the reed plate and intake from a 31.8 OMC. The bolt pattern fits so it would seem no problem but there is. Why would there be a bypass on the crank case side of the reed plate? Apparently it isn't on all of them but is on the one I'm working on. Might fill it as the 31.8 reed plate leaves it exposed to outside air. Or, would it be better to fill in a reed plate to cover it like the 22ci one does? Would this bypass be drawing crankcase compression from a decompressing cylinder or forcing compression into a compressing cylinder? Or, just balancing crank case compression? Hell if I know lol.
    Well, anyhow, Probably something like easier starts, smoother idling, but most probably not enhanced performance. I'm just going with the reed plate that fits for now. I did chamfer the reed openings to near the reed side but not past. I'll do something with the 31.8 reeds on another without the bypass channel. Thinking the larger reeds with composites, the larger fuel pump and carb might liven it up a bit.

  3. #3
    Team Member
    Join Date
    Jun 2019
    Posts
    18
    Post Thanks / Like

    Default

    Pictures are a huge help with threads like this.
    Likes JohnsonM50 liked this post

  4. #4
    Team Member JohnsonM50's Avatar
    Join Date
    Apr 2005
    Location
    Jersey
    Posts
    1,034
    Post Thanks / Like

    Default

    Quote Originally Posted by RaisedByWolves View Post
    Pictures are a huge help with threads like this.
    True, just went into putting it together tho, it's at least sounding good pending boat trial.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Compression
    By Roflhat in forum Technical Discussion
    Replies: 16
    Last Post: 06-25-2014, 08:12 AM
  2. Bypass cover
    By Buddy S in forum Technical Discussion
    Replies: 7
    Last Post: 06-11-2014, 03:32 AM
  3. Yamaha 3 cyl 40 Compression Question
    By nhpoplin in forum APBA Stock and Classic Outboard Division
    Replies: 3
    Last Post: 10-06-2013, 05:44 PM
  4. compression
    By lcp in forum Technical Discussion
    Replies: 0
    Last Post: 04-18-2011, 02:46 AM
  5. Compression variables
    By smiley in forum Technical Discussion
    Replies: 17
    Last Post: 09-19-2010, 08:05 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •