Thread: Mercury Mark 40-H

  1. #1491
    Administrator Ron Hill's Avatar
    Join Date
    Nov 2004
    Location
    Tustin, California
    Posts
    4,706
    Post Thanks / Like

    Default Long Skegs as We Called Them

    Quote Originally Posted by Aeroliner View Post
    Hi,
    Although the case is the same the drive shafts are different in the A/B unit and the C unit. The A/B has a smaller 6 spline shaft and the C has a larger diameter and 10 splines on it. Although the C shaft and D shaft look similar the D is larger. The C and D crankshaft have different splines and the foot is not interchangeable. A D crankshaft could be installed in a C block and the a D foot could be used.
    Seems to me, that the long skeg 20-H gearcase housing, to use it on a 30-H needed a larger needle bearing on the drivshaft.
    Last edited by Ron Hill; 12-18-2018 at 05:00 PM.

  2. #1492
    BoatRacingFacts VIP Aeroliner's Avatar
    Join Date
    Mar 2008
    Location
    Lake Charles, Louisiana 70611
    Posts
    924
    Post Thanks / Like

    Default

    The 30-H case became the 20-H replacement case after mercury ran out of the short castings. APBA published info on How to cut the Skeg to meet KG-4 requirements. Later Mercury made a shot case with the single water hole when they built the 25SS engines. Somewhere along the line Mercury lost the dies for the C and D cases so when the 10XS, 25XS and 44XS came out they had to go with a lost foam process for them. Also the skeg was swept back but the internals more or less were the same. Drive shaft lengths got shorter though.

  3. #1493
    Team Member MTECHMARINE's Avatar
    Join Date
    Jun 2008
    Location
    Milton Florida
    Posts
    105
    Post Thanks / Like

    Default

    Heres a powerhead service stand for the 2 shaft sizes - I believe that the Mark 30 was unique to that model alone. Ron - wasn't the difference in the driveshaft the top ball bearing rather than the needle by the pinion?

    Name:  DSC02066.JPG
Views: 734
Size:  80.1 KB

  4. #1494
    BoatRacingFacts VIP Aeroliner's Avatar
    Join Date
    Mar 2008
    Location
    Lake Charles, Louisiana 70611
    Posts
    924
    Post Thanks / Like

    Default

    Correct. They went to a metric ball bearing. Different thickness also

  5. #1495
    BoatRacingFacts VIP Aeroliner's Avatar
    Join Date
    Mar 2008
    Location
    Lake Charles, Louisiana 70611
    Posts
    924
    Post Thanks / Like

    Default Mercury 40 cubic inch pistons

    I have been working with Wiseco on a Mercury 40 cubic inch piston. I am paying for new dies and will have them in Standard, plus .020 and .040 inches oversize. My initial run will be for 50 pistons. Next run I can add .015" and .030" oversize as well if folks want them. They will be to the latest Wiseco design, improved two ring configuration and there normal coatings. I am hoping that we can sell them for $130 with rings, pins and clips. Deposit has been sent so I expect to have them in hand in 6 to 8 weeks. Let me know if you would like some in that the first run will be 50 pistons or so. Pistons are impossible to find for the D Merc so I am hoping this will help with keeping the engine in service.

    Alan

  6. #1496
    Team Member
    Join Date
    Dec 2004
    Location
    Lake Lanier (North of Atlanta, Georgia)
    Posts
    93
    Post Thanks / Like

    Default

    Quote Originally Posted by Aeroliner View Post
    I have been working with Wiseco on a Mercury 40 cubic inch piston. I am paying for new dies and will have them in Standard, plus .020 and .040 inches oversize. -Alan
    Guys, this is a BIG DEAL!! I know several others have taken small bites of this project in the past, but van Weele's are really going to save alot of old Mercury engines with this investment! Lots of old racing engines and fishing engines, too, can be put back into service with these pistons!
    Thanks!

  7. #1497
    BoatRacingFacts VIP Aeroliner's Avatar
    Join Date
    Mar 2008
    Location
    Lake Charles, Louisiana 70611
    Posts
    924
    Post Thanks / Like

    Default

    20, 40, 60 cubic inch pistons are moving forward. The forging die has been paid for and now being manufactured. Expect it to be completed in 4 weeks. Next week Wiseco will assign the part numbers for the design and I will give them a deposit for the first run. With luck we should see pistons by mid summer. I had a special size 44 piston made to save a block. For special orders You have to order 12 pistons so we have a lot of options available now.

  8. #1498
    BoatRacingFacts VIP Aeroliner's Avatar
    Join Date
    Mar 2008
    Location
    Lake Charles, Louisiana 70611
    Posts
    924
    Post Thanks / Like

    Default Yamato 250 powerheads

    I have found a couple Yamato 250 powerheads that appear to be complete and in good condition. They roll over and are not stuck. Like to get an idea of the value of these. I would like to keep one for my collection and sell the other. Anyone with info I would like your comments.

    Alan
    Attached Images Attached Images  

  9. #1499
    BoatRacingFacts VIP Aeroliner's Avatar
    Join Date
    Mar 2008
    Location
    Lake Charles, Louisiana 70611
    Posts
    924
    Post Thanks / Like

    Default Selling 3 Y-80's and parts

    Quote Originally Posted by Aeroliner View Post
    I have found a couple Yamato 250 powerheads that appear to be complete and in good condition. They roll over and are not stuck. Like to get an idea of the value of these. I would like to keep one for my collection and sell the other. Anyone with info I would like your comments.

    Alan
    In addition I am selling all my Y-80 engines and parts.
    I have 3 Yamato 80's with lots of spare parts that I am selling as a lot. It includes, pistons (new, used and oversize), ignition parts (new and used), cylinder heads, gaskets (large quantity), fuel tank and brackets, tower housings, blank lower unit foot, rope pulls (new and used) reed valves and much more more. $2,950 for everything. Photos are available.
    Attached Images Attached Images       

  10. #1500
    BoatRacingFacts VIP Aeroliner's Avatar
    Join Date
    Mar 2008
    Location
    Lake Charles, Louisiana 70611
    Posts
    924
    Post Thanks / Like

    Default

    Yamato engines and parts sold!

Thread Information

Users Browsing this Thread

There are currently 5 users browsing this thread. (0 members and 5 guests)

Similar Threads

  1. Mercury Outboard Motors
    By Skoontz in forum Outboard Racing History
    Replies: 0
    Last Post: 10-23-2006, 08:10 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •