Port work

[Hondaexp]

I have read most of the post about porting you guys posted and i figured out i know just enough to mess it up good . I have a 76 model 49 ci. 75 hp. Im looking for someone i can send it to have some work done.

[Carl Mc Williams]

What's up Johny Carol? I talked to randy today and ordered steering hub to eliminate all the trim wire tangleing up between my legs in the little yellow boat.Also saw your motor there, they need water dude. Had a problem with water pressure on mine,from being so high[ 2inchs lower than yours] but caught it before damage,thanks to pressure gauge. Anyway looking forward to this summer,we should have plenty of water since they finished dam B. I have another boat finished that we will test next warm spell.It should be faster than all of them with 25hp,if I can get prop right. Props are our biggest problem. Glad to see you post on here,I'm sure Fast Fred will answer your request soon, He's the man.
Come see me,
Carl

[Hondaexp]

Hi Carl i saw your boat on here earlier i knew i had seen that boat somewhere. I bet there are some props out at Randys that will run good. Im hoping i can get Fast Fred to port my little fishing boat motor .

[Fast Fred]

:cool:
if ya want finger ports, ya got to send the crank and pistons and rods, so i can drill the pistons and index them in the bore, can do.

[Fast Fred]

375. get ya a rendition of this map
http://aycu14.webshots.com/image/36133/2003471288060094865_rs.jpg (http://allyoucanupload.webshots.com/v/2003471288060094865)

[Hondaexp]

That sound great what pistons do you like im going to bore it . I was thinking of wisco but i read in here somewhere you said they didnt make a difference. I have some redlines in my other block they run very good.

[Fast Fred]

bein a Wiseco dealer i like them, in an indapendant test, on a Stinger power head built by Fast Fred, it showed less than 1% leak down on all cyls,
i would like to port it before it is bored, then index the ports on the pistons and drill them, my machine shop gets about 50 a hole to bore.
hears a set of them wiseco's
http://aycu37.webshots.com/image/35996/2004870600215688444_rs.jpg (http://allyoucanupload.webshots.com/v/2004870600215688444)

[Hondaexp]

Sounds good to me . Do you want me to tear it down before i send it. Its going to need to be bored 20 over i kinda melted the top piston a ball of goo stopped up the jet. Where do i send it and how do you want your money and ill get it on the way. Im not in a big hurry i have another power head i can use. My buddy Randy Green wants you to do his after mine is done.

[Fast Fred]

FastFred50borderstScituatema@@@02066&&&&&&&:eek: can do,
boring is extra, you get finger ports, the Exhaust ports, and the boost a side tranfurs get worked.;) you got to pay the shippin each way:cool:

[Randy Green]

Its boxed and ready get er done

[genetjr]

Randy put some of the pictures u got upstairs on SHOW US YOUR BOATS,enjoyed talking with ya.What every happened to Buddy Bakers boat(tunnel)that should be a quick ride with a 3 cyl omc (john/rude) Tell Ann hello See ya

[Fast Fred]

:cool:

[Carl Mc Williams]

:cool:

FF I got the 70 carbs on my 50,gained aabout 500 rpm,but took it forever to get there and very sluggish taking off. We cleaed them good and put kits in them. They have 150 jets in them now,can you tell me if that's to big and if so what size I should try?The plugs wre dark brown to black,but did not check them untill the next day. Also the 50 carbs were 25mm throats,do you know what size the 70s are? Got the freinds with stingers total attention.
Thanks Fred

[Fast Fred]

145 main jet, that will dry out the mix. i don't know what size thay are.:cool:

[Fast Fred]

when you open the throttle, this is what ya want to happen in order for best results. when ya hit it, carbs crack open Then All the timein advance drops in:eek: then the carbs go to full, full blast. loose the choke plates:eek::cool:

[MADF2000]

who said you can't do anything with them i picked up 8 mph with a different tuner and rasing the exh ports beside the fact it was on 100ml of meth to 10ml of acetone what a brew haha any other ideas not bad for a motor with no cyl head welding crank this week any othe ideas?

[MADF2000]

i also got a 31m vander velden complete motor if ya kno anyone in f3 looking to smoke the field haha take it easy guys

[Fast Fred]

a 1250cc 31m?:cool:

[MADF2000]

the 31m is about 1110cc this motor was originally avgas then we took to it with some methanol then went back to avgas but on my f3was capable of 102mph

[Mark75H]

How popular is F3 in Australia?