Page 2 of 38 FirstFirst 1234567891011121314151617181920212223242526 ... LastLast
Results 11 to 20 of 371

Thread: Johnson "70mod"

  1. #11
    Banned
    Join Date
    Nov 2016
    Posts
    289
    Post Thanks / Like

    Default

    con rods for sst60 are same as 70hp bridgeport. part number 394462 same length no different.
    piston no for sst60 and 70hp bridgeport part no 394461 same pistons.
    crankshaft for sst60 is what was used on 65, 70, 75 hp to 1986 (after that fishing motors went to multi spline) part number 328788 same throw 4 splines.

    these are all omc specs and part numbers.

    so no idea where the myth of the long rods and longer throw cranks come from.
    I do know that is what fast fred would use in a special mod 50, but not what omc used for the sst60 motor.

  2. #12
    Team Member Hevi Kevi's Avatar
    Join Date
    Jul 2013
    Posts
    23
    Post Thanks / Like

    Default

    Yes, they are the same connecting rods and cranks. No, they are not all the same size. Everything has a tolerance. This is why guys pull apart piles of engines to build one.
    Critchfield 15" 56ci OMC
    RapidCraft Cyclone 15" 56ci OMC


  3. #13
    Banned
    Join Date
    Nov 2016
    Posts
    289
    Post Thanks / Like

    Default

    not talking about guys trying to re-create a sst60 and building one up, were talking about a genuine OMC sst60 block being different to a fishing motor block.

  4. #14
    Team Member Hevi Kevi's Avatar
    Join Date
    Jul 2013
    Posts
    23
    Post Thanks / Like

    Default

    Quote Originally Posted by filthy phill View Post
    not talking about guys trying to re-create a sst60 and building one up, were talking about a genuine OMC sst60 block being different to a fishing motor block.

    ok imagine this scenario
    get a good 56 bridgeport fishing motor powerhead with say 130 psi compression. take of normal head and then put on a genuine un-molested sst60 cylinder head.
    do you think this motor would even start let alone run good ?
    It would start, run very well and likely be around 160psi

    Kevin
    Critchfield 15" 56ci OMC
    RapidCraft Cyclone 15" 56ci OMC


  5. #15
    Banned
    Join Date
    Nov 2016
    Posts
    289
    Post Thanks / Like

    Default

    would it realy
    what about the large gap where the SST60 piston normally goes into the head.
    Genuine sst60 head is not flat like the fishing motor head, it has a recess for the piston to enter.

    I would of thought compression is going to be pretty low with this head on a fishing block thats NOT been decked to allow piston entry into the head.


    .

  6. #16
    Team Member LittleCharger's Avatar
    Join Date
    Mar 2011
    Location
    London,ON,Canada
    Posts
    160
    Post Thanks / Like

    Default

    Quote Originally Posted by filthy phill View Post
    would it realy
    what about the large gap where the SST60 piston normally goes into the head.
    Genuine sst60 head is not flat like the fishing motor head, it has a recess for the piston to enter.

    I would of thought compression is going to be pretty low with this head on a fishing block thats NOT been decked to allow piston entry into the head.




    .
    The piston doesn't go into the head on a decked block, it protrudes into the head gasket.

  7. #17
    Banned
    Join Date
    Nov 2016
    Posts
    289
    Post Thanks / Like

    Default

    what ?
    you saying that you could put a fishing motor head on a genuine sst60 and the piston would not hit the head ?

  8. #18
    Team Member LittleCharger's Avatar
    Join Date
    Mar 2011
    Location
    London,ON,Canada
    Posts
    160
    Post Thanks / Like

    Default

    Quote Originally Posted by filthy phill View Post
    what ?
    you saying that you could put a fishing motor head on a genuine sst60 and the piston would not hit the head ?
    Yup because the piston doesn't stick through the head gasket.

    You need to look at the sst60 specs not sure where your getting the idea that the pocket width of the cylinder head is the diameter of the piston

  9. #19
    Team Member hupiveneilija's Avatar
    Join Date
    Oct 2014
    Location
    Finland
    Posts
    263
    Post Thanks / Like

    Default

    Quote Originally Posted by Hevi Kevi View Post
    hupiveneilija,
    Did you have any problems with the head warping when you welded up the chambers?

    Kevin
    I really dont know, havent done myself, sorry.

    I was wondering FastFreds "most positive trough" comment while ago, but then it opened to me😂. Toleranses. Thats why you need piles of motors as said.
    I have worked with one I got, allthough I got one spare yesterday to play with if Ive done something really wrong, like transfer timing😊.

  10. #20
    Team Member hupiveneilija's Avatar
    Join Date
    Oct 2014
    Location
    Finland
    Posts
    263
    Post Thanks / Like

    Default

    Some stuffing.
    Attached Images Attached Images   

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Similar Threads

  1. "Hi Johnson" - Prop Master - Story
    By Tomtall in forum Propellers
    Replies: 5
    Last Post: 06-13-2011, 05:36 AM
  2. Dennis Johnson "Trafficade" Racing
    By Ron Hill in forum Boat Racing Encyclopedia
    Replies: 1
    Last Post: 11-05-2006, 07:26 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •